Skip to main content

Posts

Showing posts with the label Linux

Connecting Xbox to your Computer! Simple

I. Introduction First you'll need a Crossover Cable : A crossover cable is needed to directly connect your computer and Xbox. You would plug one end of the cable to your computer and the other end into the Xbox, there are no devices in between. If you have a hub, switch, or router you will not need a crossover cable though some still will work with one. With connecting to hubs, switches, or routers you should use a straight-through cable. The image below shows the difference between the two: To easily tell if you have a crossover or not, simply look at the two ends side by side. If all the pins, 1 through 8 on both ends are all the same color in the same order, you have a straight-through cable. If pins 1, 3 and 2, 6 are swapped you have a crossover cable. Notice the TX, RX as well. This shows why in pc to pc connections a crossover is required. Otherwise one pc will be transmitting over the same wire the other pc is trying to transmit on. This guide currently gives configuration ...

Connecting Xbox to your Computer! Simple Part (II)

Cont... Here you've changed static ip back to yes and your gateway address should be the address of your router now. If your router is on a different subnet and by that I mean its ip is 192.168.1.1 and it is giving out dhcp address's of 192.168.1.x then you would make your evox.ini reflect those differences like this: [Network] SetupNetwork = Yes StaticIP = Yes Ip = 192.168.1.3 Subnetmask = 255.255.255.0 Defaultgateway = 192.168.1.1 DNS1 = 0.0.0.0 DNS2 = 0.0.0.0 MXM Dashboard If you run MXM as your dash and want to use DHCP then the MXM.xml file's section should look like this: True 255.255.255.0 Avalaunch Dashboard If you run Avalaunch as your dash and want to use DHCP then make the section of the avalaunch.xml look like this. 192.168.0.180 255.255.255.0 192.168.0.1 195.159.0.100 195.159.0.200 8080 UnleashX Dashboard For UnleashX, edit the config.xml file to look like this: 192.168.0.100 255.255.255.0 192.168.0.1 192.168.0.1 192.168.0.7 Yes For all of the dash's conf...

How to Securely Configure a FTP Server(BulletProof)

I am not sure where I found this tutorial, It’s been a while…It might even have been here... ..So if it is one of yours, my hat goes off to you once again.... After reading the excellent tutorial on "Creating an FTP" that Norway posted… (I would suggest reading and following his tutorial first, then following up with this one) I thought that perhaps this tutorial might be pretty helpful for those interested in knowing how to configure their Bulletproof FTP Server that don't already know how... Here's how to get started… This is for the BulletProof FTP Server 2.10. However, It should work fine on most following versions as well. I'm assuming you have it installed. Basics 1. Start the program. 2. Click on Setup > Main > General from the pull-down menu. 3. Enter your server name into the 'Server Name' box. Under Connection set the “Max number of users" to any number. This is the limit as to how many users can be on your sever at any time. 4. Click ...

Guide to avoiding virus infections with wide eyes open

Computer viruses are everywhere ! This guide will show you how to stay alert and how to avoid getting infections on your computer. Having an updated virus scanner is only a small part of this, there are many ways that you can prevent having viruses other than a virus scanner, as it will not always save you. Types of viruses There are many type of viruses. Typical viruses are simply programs or scripts that will do various damage to your computer, such as corrupting files, copying itself into files, slowly deleting all your hard drive etc. This depends on the virus. Most viruses also mail themselves to other people in the address book. This way they spread really fast and appear at others' inboxes as too many people still fall for these. Most viruses will try to convince you to open the attachment, but I have never got one that tricked me. In fact, I found myself emailing people just to make sure they really did send me something. It does not hurt to be safe. Worms Worms are differe...

A step-by-step guide to installing FreeBSD 5

A step-by-step guide to installing FreeBSD 5. It assumes moderate experience with linux and leaves you with a fully updated FreeBSD system. FreeBSD Installation A. 5.x vs 4.x The first thing to understand about FreeBSD is that there are two lines of development. The -STABLE branch is marked with a 4.x version number and the most recent version is 4.10. It is well tested and very solid, but does not include the most recent technology. The -CURRENT branch, marked with a 5.x version, is the “unstable” branch. However, it is nicely stable at the moment and is coming along quite well. Most users should go with 5.x and these instructions are only valid for that tree. NOTE: DragonFlyBSD ( www.dragonflybsd.org ) is a continuation of the 4.x line. It uses lock-less (no mutexes) SMP support and a Light Weight Kernel Threading system. It has a lot of promise and is developing at a breakneck pace, but it should still be thought of as “R/D.” B. Getting Media I am not going to say much about this. T...